Oil Change DIY for Mitsubishi Attrage

Performing an oil change is an essential maintenance task to ensure the longevity and optimal performance of your Mitsubishi Attrage. While many car owners prefer to leave this job to professionals, changing the oil yourself can be a rewarding and cost-effective DIY project. This article will guide you through the steps of changing the oil in your Mitsubishi Attrage.

1. Gather the Necessary Equipment and Supplies

• Car jack and jack stands
• Oil filter
• Socket wrench set
• Oil drain pan
• New oil filter gasket
• Funnel
• New engine oil (check the owner's manual for the recommended oil type and quantity)

2. Prepare the Vehicle

Make sure the car is parked on a flat surface and the engine is cool before starting the oil change process. Also, wear protective gloves and eyewear to ensure your safety.

3. Locate the Oil Filter and Drain Plug

On the Mitsubishi Attrage, the oil filter is usually located on the side of the engine, while the oil drain plug is situated at the bottom of the oil pan.

4. Drain the Old Oil

1. Place the oil drain pan underneath the oil pan.
2. Loosen and remove the oil drain plug using a socket wrench.
3. Allow the old oil to drain completely into the pan.
4. Once the oil has drained, reinstall the drain plug and tighten it securely.

5. Replace the Oil Filter

1. Using an oil filter wrench or your hands, remove the old oil filter.
2. Take a small amount of new engine oil and lubricate the gasket of the new oil filter.
3. Screw the new oil filter into place, making sure it is hand-tightened firmly.

6. Add New Engine Oil

1. Locate the oil filler cap on the top of the engine.
2. Using a funnel, pour the recommended amount of new engine oil into the engine.
3. Check the oil level using the dipstick and ensure it is within the recommended range.
4. Once the oil level is optimal, replace the oil filler cap.

7. Final Checks

Start the engine and let it run for a few minutes. Check for any leaks around the oil filter and drain plug. Additionally, verify that the oil pressure warning light is off.

8. Dispose of the Old Oil Properly

Used engine oil must be disposed of at a designated recycling facility. If you're unsure of where to take it, contact your local waste management department or a nearby auto store for assistance.

Performing regular oil changes is crucial for the overall health of your Mitsubishi Attrage's engine. By following these DIY steps and using the correct equipment and supplies, you can easily maintain your vehicle's performance and save money in the process. However, if you're not comfortable performing this task, it is always best to consult a professional mechanic.

Oil Change DIY for Mitsubishi Attrage

Mitsubishi Attrage is a popular compact sedan known for its fuel efficiency and reliability. Regular maintenance, such as oil changes, is crucial to keep your Mitsubishi Attrage running smoothly. While you can always visit a service center for an oil change, doing it yourself can be a cost-effective and satisfying option. In this DIY guide, we will walk you through the step-by-step process of changing oil on your Mitsubishi Attrage.

What you'll need:

• Car jack or ramps
• Oil filter wrench
• Socket wrench or adjustable wrench
• New oil filter
• New engine oil
• Oil drain pan
• Funnel
• Clean cloth

Step 1: Preparation

Start by ensuring you have all the necessary tools and materials mentioned above before getting started. Park your Mitsubishi Attrage on a flat surface and wait for the engine to cool down to prevent any injuries.

Step 2: Lift the car

Use a car jack or ramps to lift the front of your car. Make sure you secure it properly to avoid any accidents. Locate the oil pan under the engine.

Step 3: Remove the drain plug

Position the oil drain pan underneath the drain plug and use a socket wrench or adjustable wrench to carefully remove the drain plug. Allow the old oil to drain completely into the pan.

Step 4: Replace the oil filter

Locate the oil filter, which is usually at the front or side of the engine. Use an oil filter wrench to remove the old oil filter. Clean any oil residue from the filter housing and apply a thin layer of new oil to the rubber gasket on the new oil filter. Install the new oil filter by hand and tighten it securely.

Step 5: Add new oil

Locate the oil filler cap on top of the engine. Unscrew it and place a funnel inside the opening. Pour the appropriate amount and type of new engine oil into the funnel. Check your vehicle's owner's manual for the recommended oil type and capacity. It is advisable to pour in small quantities at a time, allowing the oil to settle before adding more.

Step 6: Check oil level and clean up

Once you have poured in the recommended amount of oil, remove the funnel and wipe any spilled oil. Screw the oil filler cap back on tightly. Start your Mitsubishi Attrage and let it run for a few minutes. Turn off the engine and wait for a minute or two. Now, check the oil level using the dipstick. Add more oil if needed, but make sure not to overfill it.

Step 7: Dispose of old oil responsibly

Pour the old oil from the drain pan into a suitable container and take it to your nearest recycling center. Never dispose of used oil in the regular trash or pour it down the drain as it is harmful to the environment.

By following these simple steps, you can successfully change the oil in your Mitsubishi Attrage, saving money and maintaining the performance of your vehicle. However, always refer to your vehicle's manual for specific instructions and consult a professional if you are unsure or uncomfortable performing the task on your own.